CVA6 Platform

CVA6 Platform is a multi-core CVA6 with CV-MESH intended for software testing and regression.

Genesys II: Getting Started

1. Download the pre-built bitstream from downloads.openhwgroup.org.
2. Put it on a FAT32 formatted USB stick.
3. Insert the USB stick into the top USB port on the Genesys II board. Set the JP5 to switch to USB/SD and JP4 to USB, this will use the bitstream on the pendrive (more detailed instructions can be found here).
4. Download the Fedora image from downloads.openhwgroup.org.
5. gunzip and flash the image on an SDCard using BalenaEtcher.
6. Power on the board and play tetris.

Build instructions for Genesys2

General Overview:

1. Compile bitstream
2. Generate fw_payload.bin
3. Build Linux
4. Copy fw_payload.bin and Image into /boot/
5. Boot Linux

Detailed Look:

0. Initialization We assume you have a xpack-riscv-none-embed prebuilt riscv cross-compiler installed in ~/tools/ and have

export RISCV_TOOLCHAIN=$HOME/tools/xpack-riscv-none-embed-gcc-10.2.0-1.2 export PATH=$PATH:$RISCV_TOOLCHAIN/bin

in your .bashrc.

1. Compiling Bitstream

To compile the bitstream, clone the openpiton repo (openpiton-dev branch) and then

git clone [email protected]:PrincetonUniversity/openpiton.git -b openpiton-dev cd openpiton

Make sure the necessary submodules are updated using:

git submodule update --init --recursive piton/design/chip/tile/ariane git submodule update --init --recursive piton/design/chipset/rv64_platform/bootrom/u-boot/uboot

Navigate to the openpiton directory and run

export PITON_ROOT=$PWD export ARIANE_ROOT=$PITON_ROOT/piton/design/chip/tile/ariane source piton/piton_settings.bash

Then run source your Vivado setup, e.g.:

source /tools/Xilinx/Vivado/2022.1/settings64.sh

Generate the bitstream with

protosyn -b genesys2 -d system -c ariane --x_tiles=2 --y_tiles=1 --linux_bootrom=uboot

2. Generating fw_payload.bin

Navigate to ./piton/design/chipset/rv64_platform/bootrom/u-boot/uboot.

Run make distclean.

Apply the non-spl defconfig using make ARCH=riscv CROSS_COMPILE=riscv-none-embed- openpiton_riscv64_defconfig.

Re-build u-boot-nodtb using make ARCH=riscv CROSS_COMPILE=riscv-none-embed- -j8.

Clone opensbi 1.0 to your preferred directory using:

git clone [email protected]:riscv-software-src/opensbi.git cd opensbi git checkout v1.0 ARCH=riscv CROSS_COMPILE=riscv-none-embed- make PLATFORM=fpga/openpiton FW_PAYLOAD_PATH=$PITON_ROOT/piton/design/chipset/rv64_platform/bootrom/u-boot/uboot/u-boot-nodtb.bin

3. Building Linux

git clone [email protected]:openpiton/linux.git -b cva6platform-6.2

Here we assume you'll use the committed .config for your build.

Build the kernel using make ARCH=riscv CROSS_COMPILE=riscv-none-embed- -j8 (assuming you want to use 8 threads).

4. Copying into SD card

First, mount the SD card. Run lsblk to find out the name of the disk's first partition, e.g. /dev/sdb1 but please be very careful and double and triple check. Then, run e.g. sudo mount /dev/sdb1 mntdir/ where mntdir/ is the name of an empty directory. Alternatively if your distro automounts the SD, you can just move on to copying the files below.

Copy arch/riscv/boot/Image (from your linux build) and build/platform/fpga/openpiton/firmware/fw_payload.bin (from your opensbi build) into mntdir/boot/ of the SD card, and run sync to ensure the data is copied properly, and then run sudo umount mntdir/ to safely remove the SD card.

Copy your build/genesys2/system/genesys2_system/genesys2_system.runs/impl_1/system.bit (from your openpiton build) onto a USB drive for programming the FPGA.

5. Boot

Plug the USB into the top USB port and insert the SD card and boot up the FPGA.